Outboard Jets at Troutt and Son’s Inc. St. James Mo. PHONE: 573-265-3456  FAX: 573-265-1100This image has an empty alt attribute; its file name is HELP-WANTED-AD-4.jpg

Outboard Jet Units

Outboard Jet Units

For over 40 years, Outboard Jets has provided quality conversion units for outboard motors designed to allow a boat to be used in locations where a propeller driven boat is unable to operate – in shallow, ankle deep water.

How does it work? Like Newton’s Third Law says, “For every force, there is an equal and opposite force of reaction.” Water is drawn into the unit through an intake grill by an impeller driven directly by the engine driveshaft. This water is then forced at high pressure and volume through a nozzle directed astern of the boat. The velocity imparted to this mass of water creates an opposite force, and drives the boat forward. Experience the excitement and satisfaction of going boating with an Outboard Jet, where propeller driven craft cannot go!

Outboard Jet UnitCombining the correct outboard power and boat design is the “secret” of successfully using an outboard jet to run in shallow water. After reading this information, please read the “Outboard Jets” brochure. These two pieces of information will assist you in selecting the best combination for your needs, thereby giving you the advantages of outboard power for shallow water use. To receive an Outboard Jet brochure, call (510) 562-6049.

Most important is the boat. Keep it light as possible since, unlike a propeller drive, you can’t change to a lower pitch jet drive impeller to increase load capability.

Aluminum is usually the material of choice. It is light, tough and easy to form in the proper configuration. For outboard jets, the bottom thickness can range from 1/16” (.063) for 20-50 HP to 3/16” (.187) for motors up to 225 HP. The lighter gauge is more easily damaged whereas the heaviest gauge can be a weight problem on midrange power from 50-100 HP.

The size and shape of the bottom is very important. The object is to ride on top of the water, which requires a good planing surface, and to float as shallow as possible when shut down. Bottom should be at least 48 inches wide and boat length at least 14 feet long. Air entering the jet drive causes slippage, so the boat bottom needs to supply solid water, free of air, to the jet drive intake. No one boat can satisfy every need, so choices must be made. With this thought in mind, some pros and cons of various boat types are noted below.

A flat bottom boat runs shallower than a vee bottom, but slides on the turns more. A vee bottom splits off air bubbles before they reach the jet intake. A flat bottom carries bubbles straight back.

An aluminum flat bottom with a 48 inch (4 ft.) bottom (45HP) and 14 ft. overall. This design works well, but will ingest some air when running with the wind in a chop. This can be helped by the use of intake fin side skirts.

A slight V of 6-10 degrees dead rise will enhance jet boat handling. Deep vee is not desirable for the Outboard Jet, not just because of increased draft and drag, But because the Outboard Jet needs a flat apron of water about 10” wide leaving the hull on which to set the leading edge of the jet intake, to minimize air intake and frontal drag. The dead rise should be fairly constant and not increase to a deep forefoot at the bow. A deep forefoot can cause spinout on a sharp turn.

Outboard Jet UnitKeels can be a problem, introducing air into the jet intake. Center keels vary in size and may introduce air. If this is suspected, the keel should be removed 2-3 feet forward of the transom. Other keel arrangements which tend to funnel air to the jet intake should be avoided.

The chines of the boat, where the sides meet the bottom, should be sharp. Round chimes tend to suck the boat down in the water and cause drag.

A properly designed tunnel, combined with a slight V bottom hull can greatly enhance jet boat performance. It should raise the motor 2-3 inches and place the heel of the jet intake flush or slightly above the bottom of the boat. A jet tunnel doesn’t work well with a flat bottom boat due to air ingestion. It’s imperative that the hull is designed correctly with the tunnel for the boat to operate properly.

The tunnel needs to be just large enough to feed the jet drive its water requirements. A tunnel that is longer, wider or deeper than necessary wastes power in lifting excess water, tends to suck the stern down when planing and sits deeper in the water at rest due to lost buoyancy.

The top of the tunnel width should be about 1 ¾ times the width of the jet drive water intake. The tunnel length doesn’t have to be longer than about 2 ½ times the water intake width.

Make every river longer with Outboard Jets

Inflatables are light, easy to transport, bounce off the rocks nicely but due to the flexible nature of their bottom they trap and introduce air into the jet intake. Steering is squirrelly when running light and in crosswinds. Even so, we get calls from our customers who are very happy with their inflatable.

A rigid hull inflatable on the other hand can’t be folded to fit inside your car, but steers better and provides solid water to the intake. Unfortunately, the hulls presently available have more than 10 degrees of dead rise.

Pontoon boats don’t provide a defined height apron of water ahead of the jet intake. The water level between the pontoons varies with speed and load carried. It’s necessary to build an inclined plane ahead of the jet intake attached to the motor mount, about 16” wide inclined at about 15 degrees with the leading edge above water level, fully loaded at rest, trailing edge lined up with the leading edge of the jet intake.

Outboard Jet Units

Motor Specials